feat: 全量同步 254 个常用的 Arduino 扩展库文件

arduino-libs/arduino-cli/libraries/PinChangeInterrupt/src/PinChangeInterruptSettings.h

@@ -0,0 +1,230 @@
+/*
+Copyright (c) 2014-2021 NicoHood
+See the readme for credit to other people.
+
+Permission is hereby granted, free of charge, to any person obtaining a copy
+of this software and associated documentation files (the "Software"), to deal
+in the Software without restriction, including without limitation the rights
+to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+copies of the Software, and to permit persons to whom the Software is
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in
+all copies or substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+THE SOFTWARE.
+*/
+
+// include guard
+#pragma once
+
+//================================================================================
+// General Settings
+//================================================================================
+
+/* Settings to de/activate ports/pins
+This will save you flash and ram because the arrays
+are managed dynamically with the definitions below.
+Make sure you still have all needed ports activated.
+Each deactivated port saves 3 bytes of ram.
+If you deactivate the whole port,
+you dont need to deactivate the pins.
+Same for the port if you deactivate all 8 pins.
+You dont have to deactivate pins/ports that dont exist.
+That is done by the macros. */
+
+#ifndef PCINT_ENABLE_MANUAL
+
+#define PCINT_ENABLE_PORT0
+#define PCINT_ENABLE_PORT1
+#define PCINT_ENABLE_PORT2
+#define PCINT_ENABLE_PORT3
+
+#define PCINT_ENABLE_PCINT0
+#define PCINT_ENABLE_PCINT1
+#define PCINT_ENABLE_PCINT2
+#define PCINT_ENABLE_PCINT3
+#define PCINT_ENABLE_PCINT4
+#define PCINT_ENABLE_PCINT5
+#define PCINT_ENABLE_PCINT6
+#define PCINT_ENABLE_PCINT7
+#define PCINT_ENABLE_PCINT8
+#define PCINT_ENABLE_PCINT9
+#define PCINT_ENABLE_PCINT10
+#define PCINT_ENABLE_PCINT11
+#define PCINT_ENABLE_PCINT12
+#define PCINT_ENABLE_PCINT13
+#define PCINT_ENABLE_PCINT14
+#define PCINT_ENABLE_PCINT15
+#define PCINT_ENABLE_PCINT16
+#define PCINT_ENABLE_PCINT17
+#define PCINT_ENABLE_PCINT18
+#define PCINT_ENABLE_PCINT19
+#define PCINT_ENABLE_PCINT20
+#define PCINT_ENABLE_PCINT21
+#define PCINT_ENABLE_PCINT22
+#define PCINT_ENABLE_PCINT23
+#define PCINT_ENABLE_PCINT24
+#define PCINT_ENABLE_PCINT25
+#define PCINT_ENABLE_PCINT26
+#define PCINT_ENABLE_PCINT27
+#define PCINT_ENABLE_PCINT28
+#define PCINT_ENABLE_PCINT29
+#define PCINT_ENABLE_PCINT30
+#define PCINT_ENABLE_PCINT31
+
+#endif
+
+#ifdef ARDUINO
+// use API with function pointers (better optimized with .a linkage)
+#define PCINT_API
+
+// is the library compiled via .a file?
+// see readme for more information
+#define PCINT_ALINKAGE
+
+// force compile all enabled port ISRs (with .a linkage)
+//#define PCINT_COMPILE_ENABLED_ISR
+
+#endif
+
+//================================================================================
+// Suggested Settings
+//================================================================================
+
+// Arduino Uno (328)
+#if defined(__AVR_ATmega328__) || defined(__AVR_ATmega328P__) || defined(__AVR_ATmega168__) || defined(__AVR_ATmega88__)
+/* Reordering interrupt callbacks priority
+Port0 has SPI on higher pins, ordering is fine
+Port1 has I2C on higher pins, ordering is fine
+Port2 has USART and Pin Interrupt on lower pins,
+move the priority down
+Its more likely the user will use pin 4-7
+*/
+#if !defined(PCINT_CALLBACK_PORT2)
+#define PCINT_CALLBACK_PORT2 \
+PCINT_CALLBACK(4, 20); \
+PCINT_CALLBACK(5, 21); \
+PCINT_CALLBACK(6, 22); \
+PCINT_CALLBACK(7, 23); \
+PCINT_CALLBACK(0, 16); /* USART RX */ \
+PCINT_CALLBACK(1, 17); /* USART TX */ \
+PCINT_CALLBACK(2, 18); /* Pin Interrupt 0 */ \
+PCINT_CALLBACK(3, 19); /* Pin Interrupt 1 */
+#endif
+
+// deactivate crystal and reset pins by default
+#if defined(PCINT_ENABLE_PCINT6)
+#undef PCINT_ENABLE_PCINT6 // crystal
+#endif
+#if defined(PCINT_ENABLE_PCINT7)
+#undef PCINT_ENABLE_PCINT7 // crystal
+#endif
+#if defined(PCINT_ENABLE_PCINT14)
+#undef PCINT_ENABLE_PCINT14 // reset
+#endif
+#endif
+
+// Arduino Mega (2560)
+#if defined(ARDUINO_AVR_MEGA2560) || defined(ARDUINO_AVR_MEGA)
+/* Port1 is structured a bit more complicated
+Also only 3 pins are connected on standard boards
+Seeeduino Mega has these pins optional!
+Disabling Port1 gives more speed and uses less flash
+Pins: 0(RX0), 14(TX3), 15(RX3) */
+#if defined(PCINT_ENABLE_PORT1)
+#undef PCINT_ENABLE_PORT1 // better performence
+#endif
+
+/* Reordering interrupt callbacks priority
+Port2 has SPI on lower pins, move the priority down
+Its more likely the user will use pin 10-13
+Port1 by default deactivated, ordering is fine
+Port2 only has ADCs, ordering is fine
+*/
+#if !defined(PCINT_CALLBACK_PORT0)
+#define PCINT_CALLBACK_PORT0 \
+PCINT_CALLBACK(4, 4); \
+PCINT_CALLBACK(5, 5); \
+PCINT_CALLBACK(6, 6); \
+PCINT_CALLBACK(7, 7); \
+PCINT_CALLBACK(0, 0); /* SPI SS */ \
+PCINT_CALLBACK(1, 1); /* SPI SCK */ \
+PCINT_CALLBACK(2, 2); /* SPI MISO */ \
+PCINT_CALLBACK(3, 3); /* SPI MOSI */
+#endif
+#endif
+
+// Arduino Leonardo/Micro (32u4)
+#if defined(__AVR_ATmega32U4__) || defined(__AVR_ATmega16U4__)
+/* Reordering interrupt callbacks priority
+Port0 has SPI on lower pins, move the priority down
+Its more likely the user will use pin 8-11 */
+#if !defined(PCINT_CALLBACK_PORT0)
+#define PCINT_CALLBACK_PORT0 \
+PCINT_CALLBACK(4, 4); \
+PCINT_CALLBACK(5, 5); \
+PCINT_CALLBACK(6, 6); \
+PCINT_CALLBACK(7, 7); \
+PCINT_CALLBACK(0, 0); /* SPI SS / RX LED */ \
+PCINT_CALLBACK(1, 1); /* SPI SCK */ \
+PCINT_CALLBACK(2, 2); /* SPI MISO */ \
+PCINT_CALLBACK(3, 3); /* SPI MOSI */
+#endif
+
+// RX LED on normal leonardo/micro
+#if defined(PCINT_ENABLE_PCINT0) && (defined(ARDUINO_AVR_LEONARDO) || defined(ARDUINO_AVR_MICRO))
+#undef PCINT_ENABLE_PCINT0
+#endif
+#endif
+
+// Hoodloader2 (u2 Series)
+#if defined(__AVR_AT90USB82__) || defined(__AVR_AT90USB162__) || defined(__AVR_ATmega32U2__) || defined(__AVR_ATmega16U2__) || defined(__AVR_ATmega8U2__)
+#if defined(ARDUINO_HOODLOADER2)
+// on HoodLoader2 Arduino boards only PB1-7 (port0) is broken out, save this flash
+#if defined(PCINT_ENABLE_PORT1)
+#undef PCINT_ENABLE_PORT1
+#endif
+
+// SS (PB0) is not connected on normal Arduino boards
+#if defined(PCINT_ENABLE_PCINT0)
+#undef PCINT_ENABLE_PCINT0
+#endif
+
+/* Reordering interrupt callbacks priority
+Port0 has SPI on lower pins, move the priority down
+Its more likely the user will use PB4-7
+Pretend the User has not soldered the 4 Pinheader
+so only do this for non Arduino boards. */
+#else
+#if !defined(PCINT_CALLBACK_PORT0)
+#define PCINT_CALLBACK_PORT0 \
+PCINT_CALLBACK(4, 4); \
+PCINT_CALLBACK(5, 5); \
+PCINT_CALLBACK(6, 6); \
+PCINT_CALLBACK(7, 7); \
+PCINT_CALLBACK(0, 0); /* SPI SS */ \
+PCINT_CALLBACK(1, 1); /* SPI SCK */ \
+PCINT_CALLBACK(2, 2); /* SPI MISO */ \
+PCINT_CALLBACK(3, 3); /* SPI MOSI */
+#endif
+#endif
+#endif
+
+/* Attiny 25/45/85 only has a very few pins
+activate all by default
+The order is also okay. */
+
+#if defined(__AVR_ATtiny24__) || defined(__AVR_ATtiny44__) || defined(__AVR_ATtiny84__)
+// Port1 is connected to reset, crystal and Pin Interrupt 0
+// Deactivate it by default
+#if defined(PCINT_ENABLE_PORT1)
+#undef PCINT_ENABLE_PORT1
+#endif
+#endif