初始化提交

2024-07-20 22:09:06 +08:00
commit c247dd07a6
6876 changed files with 2743096 additions and 0 deletions
--- a/arduino-cli/libraries/IRremoteESP8266/examples/IRsendProntoDemo/IRsendProntoDemo.ino
+++ b/arduino-cli/libraries/IRremoteESP8266/examples/IRsendProntoDemo/IRsendProntoDemo.ino
@@ -0,0 +1,114 @@
+/* IRremoteESP8266: IRsendProntoDemo
+ * Copyright 2017 David Conran
+ *
+ * Demonstrates sending Pronto codes with IRsend.
+ *
+ * Version 1.0 June, 2017
+ *
+ * An IR LED circuit *MUST* be connected to ESP8266 pin 4 (D2), unless you
+ * change the kIrLed value below.
+ *
+ * TL;DR: The IR LED needs to be driven by a transistor for a good result.
+ *
+ * Suggested circuit:
+ *     https://github.com/crankyoldgit/IRremoteESP8266/wiki#ir-sending
+ *
+ * Common mistakes & tips:
+ *   * Don't just connect the IR LED directly to the pin, it won't
+ *     have enough current to drive the IR LED effectively.
+ *   * Make sure you have the IR LED polarity correct.
+ *     See: https://learn.sparkfun.com/tutorials/polarity/diode-and-led-polarity
+ *   * Typical digital camera/phones can be used to see if the IR LED is flashed.
+ *     Replace the IR LED with a normal LED if you don't have a digital camera
+ *     when debugging.
+ *   * Avoid using the following pins unless you really know what you are doing:
+ *     * Pin 0/D3: Can interfere with the boot/program mode & support circuits.
+ *     * Pin 1/TX/TXD0: Any serial transmissions from the ESP8266 will interfere.
+ *     * Pin 3/RX/RXD0: Any serial transmissions to the ESP8266 will interfere.
+ *   * ESP-01 modules are tricky. We suggest you use a module with more GPIOs
+ *     for your first time. e.g. ESP-12 etc.
+ */
+
+#include <Arduino.h>
+#include <IRremoteESP8266.h>
+#include <IRsend.h>
+
+const uint16_t kIrLed = 4;  // ESP8266 GPIO pin to use. Recommended: 4 (D2).
+
+IRsend irsend(kIrLed);  // Set the GPIO to be used to sending the message.
+
+// Panasonic Plasma TV Descrete code (Power On).
+// Acquired from:
+//   https://irdb.globalcache.com/
+// e.g.
+// 0000 006D 0000 0022 00ac 00ac 0016 0040 0016 0040 0016 0040 0016 0015 0016
+// 0015 0016 0015 0016 0015 0016 0015 0016 0040 0016 0040 0016 0040 0016 0015
+// 0016 0015 0016 0015 0016 0015 0016 0015 0016 0040 0016 0015 0016 0015 0016
+// 0040 0016 0040 0016 0015 0016 0015 0016 0040 0016 0015 0016 0040 0016 0040
+// 0016 0015 0016 0015 0016 0040 0016 0040 0016 0015 0016 071c
+//
+// Or the equiv. of sendSamsung(0xE0E09966);
+uint16_t samsungProntoCode[72] = {
+    0x0000, 0x006D, 0x0000, 0x0022,
+    0x00ac, 0x00ac, 0x0016, 0x0040, 0x0016, 0x0040, 0x0016, 0x0040,
+    0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0015,
+    0x0016, 0x0015, 0x0016, 0x0040, 0x0016, 0x0040, 0x0016, 0x0040,
+    0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0015,
+    0x0016, 0x0015, 0x0016, 0x0040, 0x0016, 0x0015, 0x0016, 0x0015,
+    0x0016, 0x0040, 0x0016, 0x0040, 0x0016, 0x0015, 0x0016, 0x0015,
+    0x0016, 0x0040, 0x0016, 0x0015, 0x0016, 0x0040, 0x0016, 0x0040,
+    0x0016, 0x0015, 0x0016, 0x0015, 0x0016, 0x0040, 0x0016, 0x0040,
+    0x0016, 0x0015, 0x0016, 0x071c
+};
+
+// Panasonic Plasma TV Descrete code (Power On).
+// Acquired from:
+//   ftp://ftp.panasonic.com/pub/panasonic/drivers/monitors/Discrete-remote-control-codesProntoCCFformat.pdf
+// e.g.
+// 0000 0071 0000 0032 0080 003F 0010 0010 0010 0030 0010 0010 0010 0010 0010
+// 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010
+// 0010 0010 0010 0030 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010
+// 0010 0010 0010 0010 0010 0010 0010 0010 0030 0010 0010 0010 0010 0010 0010
+// 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0010 0030 0010
+// 0030 0010 0030 0010 0030 0010 0030 0010 0010 0010 0010 0010 0010 0010 0030
+// 0010 0030 0010 0030 0010 0030 0010 0030 0010 0010 0010 0030 0010 0A98
+//
+// Or the equiv. of sendPanasonic64(0x400401007C7D);
+uint16_t panasonicProntoCode[104] = {
+    0x0000, 0x0071, 0x0000, 0x0032,
+    0x0080, 0x003F, 0x0010, 0x0010, 0x0010, 0x0030, 0x0010, 0x0010,
+    0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
+    0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
+    0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0030, 0x0010, 0x0010,
+    0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
+    0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
+    0x0010, 0x0030, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
+    0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0010,
+    0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0030, 0x0010, 0x0030,
+    0x0010, 0x0030, 0x0010, 0x0030, 0x0010, 0x0030, 0x0010, 0x0010,
+    0x0010, 0x0010, 0x0010, 0x0010, 0x0010, 0x0030, 0x0010, 0x0030,
+    0x0010, 0x0030, 0x0010, 0x0030, 0x0010, 0x0030, 0x0010, 0x0010,
+    0x0010, 0x0030, 0x0010, 0x0A98};
+
+void setup() {
+  irsend.begin();
+  #if defined(ESP8266)
+    Serial.begin(115200, SERIAL_8N1, SERIAL_TX_ONLY);
+  #else  // ESP8266
+    Serial.begin(115200, SERIAL_8N1);
+  #endif  // ESP8266
+}
+
+void loop() {
+#if SEND_PRONTO
+  Serial.println("Sending a Samsung TV 'on' command.");
+  irsend.sendPronto(samsungProntoCode, 72);
+  delay(2000);
+  Serial.println("Sending a Panasonic Plasma TV 'on' command.");
+  irsend.sendPronto(panasonicProntoCode, 104);
+  delay(2000);
+#else  // SEND_PRONTO
+  Serial.println("Can't send because SEND_PRONTO has been disabled.");
+  delay(10000);
+#endif  // SEND_PRONTO
+}