初始化提交

arduino-cli/libraries/IRremoteESP8266/examples/IRrecvDump/IRrecvDump.ino

@@ -0,0 +1,102 @@
+/*
+ * IRremoteESP8266: IRrecvDump - dump details of IR codes with IRrecv
+ * Copyright 2009 Ken Shirriff, http://arcfn.com
+ *
+ ***** DEPRECATED - DO NOT USE *****
+ * Unless you know what you are doing, you should be using the
+ * IRrecvDumpV2.ino sketch/example instead for capturing & decoding IR messages.
+ * In almost ALL ways it is BETTER, FASTER, and MORE DETAILED.
+ *
+ * This code is left only for legacy reasons, and as another simple example of
+ * how to use the IRremoteESP8266 library.
+ *
+ * As of November 2017 it will no longer be updated or supported.
+ * You have been warned.
+ ***** DEPRECATED - DO NOT USE *****
+ *
+ * An IR detector/demodulator must be connected to the input RECV_PIN.
+ * Version 0.2 Oct 2017
+ * Based on Ken Shirriff's IrsendDemo Version 0.1 July, 2009,
+ * JVC and Panasonic protocol added by Kristian Lauszus
+ *   (Thanks to zenwheel and other people at the original blog post)
+ * LG added by Darryl Smith (based on the JVC protocol)
+ */
+
+#include <Arduino.h>
+#include <IRremoteESP8266.h>
+#include <IRrecv.h>
+#include <IRutils.h>
+
+// an IR detector/demodulator is connected to GPIO pin 2
+uint16_t RECV_PIN = 2;
+
+IRrecv irrecv(RECV_PIN);
+
+decode_results results;
+
+void setup() {
+  Serial.begin(115200);
+  irrecv.enableIRIn();  // Start the receiver
+}
+
+void dump(decode_results *results) {
+  // Dumps out the decode_results structure.
+  // Call this after IRrecv::decode()
+  uint16_t count = results->rawlen;
+  if (results->decode_type == UNKNOWN) {
+    Serial.print("Unknown encoding: ");
+  } else if (results->decode_type == NEC) {
+    Serial.print("Decoded NEC: ");
+  } else if (results->decode_type == SONY) {
+    Serial.print("Decoded SONY: ");
+  } else if (results->decode_type == RC5) {
+    Serial.print("Decoded RC5: ");
+  } else if (results->decode_type == RC5X) {
+    Serial.print("Decoded RC5X: ");
+  } else if (results->decode_type == RC6) {
+    Serial.print("Decoded RC6: ");
+  } else if (results->decode_type == RCMM) {
+    Serial.print("Decoded RCMM: ");
+  } else if (results->decode_type == PANASONIC) {
+    Serial.print("Decoded PANASONIC - Address: ");
+    Serial.print(results->address, HEX);
+    Serial.print(" Value: ");
+  } else if (results->decode_type == LG) {
+    Serial.print("Decoded LG: ");
+  } else if (results->decode_type == JVC) {
+    Serial.print("Decoded JVC: ");
+  } else if (results->decode_type == AIWA_RC_T501) {
+    Serial.print("Decoded AIWA RC T501: ");
+  } else if (results->decode_type == WHYNTER) {
+    Serial.print("Decoded Whynter: ");
+  } else if (results->decode_type == NIKAI) {
+    Serial.print("Decoded Nikai: ");
+  }
+  serialPrintUint64(results->value, 16);
+  Serial.print(" (");
+  Serial.print(results->bits, DEC);
+  Serial.println(" bits)");
+  Serial.print("Raw (");
+  Serial.print(count, DEC);
+  Serial.print("): {");
+
+  for (uint16_t i = 1; i < count; i++) {
+    if (i % 100 == 0)
+      yield();  // Preemptive yield every 100th entry to feed the WDT.
+    if (i & 1) {
+      Serial.print(results->rawbuf[i] * kRawTick, DEC);
+    } else {
+      Serial.print(", ");
+      Serial.print((uint32_t) results->rawbuf[i] * kRawTick, DEC);
+    }
+  }
+  Serial.println("};");
+}
+
+void loop() {
+  if (irrecv.decode(&results)) {
+    dump(&results);
+    Serial.println("DEPRECATED: Please use IRrecvDumpV2.ino instead!");
+    irrecv.resume();  // Receive the next value
+  }
+}

arduino-cli/libraries/IRremoteESP8266/examples/IRrecvDump/platformio.ini

@@ -0,0 +1,18 @@
+[platformio]
+src_dir = .
+
+[env]
+lib_extra_dirs = ../../
+lib_ldf_mode = deep+
+lib_ignore = examples
+framework = arduino
+monitor_speed = 115200
+build_flags = ; -D_IR_LOCALE_=en-AU
+
+[env:nodemcuv2]
+platform = espressif8266
+board = nodemcuv2
+
+[env:esp32dev]
+platform = espressif32
+board = esp32dev