初始化提交

arduino-cli/libraries/IRremoteESP8266/examples/IRGCSendDemo/IRGCSendDemo.ino

@@ -0,0 +1,70 @@
+/*
+ * IRremoteESP8266: IRsendGCDemo
+ * demonstrates sending Global Cache-formatted IR codes with IRsend
+ * Copyright 2009 Ken Shirriff
+ * http://arcfn.com
+ *
+ * Version 0.2 June, 2017
+ *   Added helpful comments
+ *   Better includes files.
+ * Version 0.1 30 March, 2016
+ *   Based on Ken Shirriff's IrsendDemo
+ *   Version 0.1 July, 2009
+ *
+ * An IR LED circuit *MUST* be connected to the ESP8266 on a pin
+ * as specified by IR_LED below.
+ *
+ * TL;DR: The IR LED needs to be driven by a transistor for a good result.
+ *
+ * Suggested circuit:
+ *     https://github.com/crankyoldgit/IRremoteESP8266/wiki#ir-sending
+ *
+ * Common mistakes & tips:
+ *   * Don't just connect the IR LED directly to the pin, it won't
+ *     have enough current to drive the IR LED effectively.
+ *   * Make sure you have the IR LED polarity correct.
+ *     See: https://learn.sparkfun.com/tutorials/polarity/diode-and-led-polarity
+ *   * Typical digital camera/phones can be used to see if the IR LED is
+ * flashed. Replace the IR LED with a normal LED if you don't have a digital
+ * camera when debugging.
+ *   * Avoid using the following pins unless you really know what you are doing:
+ *     * Pin 0/D3: Can interfere with the boot/program mode & support circuits.
+ *     * Pin 1/TX/TXD0: Any serial transmissions from the ESP8266 will
+ * interfere.
+ *     * Pin 3/RX/RXD0: Any serial transmissions to the ESP8266 will interfere.
+ *   * ESP-01 modules are tricky. We suggest you use a module with more GPIOs
+ *     for your first time. e.g. ESP-12 etc.
+ */
+
+#include <Arduino.h>
+#include <IRremoteESP8266.h>
+#include <IRsend.h>
+
+// Codes are in Global Cache format less the emitter ID and request ID.
+// These codes can be found in GC's Control Tower database.
+
+uint16_t Samsung_power_toggle[71] = {
+    38000, 1,  1,  170, 170, 20, 63, 20, 63, 20, 63,  20, 20, 20, 20,
+    20,    20, 20, 20,  20,  20, 20, 63, 20, 63, 20,  63, 20, 20, 20,
+    20,    20, 20, 20,  20,  20, 20, 20, 20, 20, 63,  20, 20, 20, 20,
+    20,    20, 20, 20,  20,  20, 20, 20, 20, 63, 20,  20, 20, 63, 20,
+    63,    20, 63, 20,  63,  20, 63, 20, 63, 20, 1798};
+
+#define IR_LED 4  // ESP8266 GPIO pin to use. Recommended: 4 (D2).
+
+IRsend irsend(IR_LED);  // Set the GPIO to be used to sending the message.
+
+void setup() {
+  irsend.begin();
+  Serial.begin(115200);
+}
+
+void loop() {
+  Serial.println("Toggling power");
+#if SEND_GLOBALCACHE
+  irsend.sendGC(Samsung_power_toggle, 71);
+#else   // SEND_GLOBALCACHE
+  Serial.println("Can't send because SEND_GLOBALCACHE has been disabled.");
+#endif  // SEND_GLOBALCACHE
+  delay(10000);
+}

arduino-cli/libraries/IRremoteESP8266/examples/IRGCSendDemo/platformio.ini

@@ -0,0 +1,18 @@
+[platformio]
+src_dir = .
+
+[env]
+lib_extra_dirs = ../../
+lib_ldf_mode = deep+
+lib_ignore = examples
+framework = arduino
+monitor_speed = 115200
+build_flags = ; -D_IR_LOCALE_=en-AU
+
+[env:nodemcuv2]
+platform = espressif8266
+board = nodemcuv2
+
+[env:esp32dev]
+platform = espressif32
+board = esp32dev