初始化提交

arduino-cli/libraries/Adafruit_Fingerprint_Sensor_Library/examples/delete/delete.ino

@@ -0,0 +1,100 @@
+/***************************************************
+  This is an example sketch for our optical Fingerprint sensor
+
+  Designed specifically to work with the Adafruit Fingerprint sensor
+  ----> http://www.adafruit.com/products/751
+
+  These displays use TTL Serial to communicate, 2 pins are required to
+  interface
+  Adafruit invests time and resources providing this open source code,
+  please support Adafruit and open-source hardware by purchasing
+  products from Adafruit!
+
+  Written by Limor Fried/Ladyada for Adafruit Industries.
+  BSD license, all text above must be included in any redistribution
+ ****************************************************/
+
+#include <Adafruit_Fingerprint.h>
+
+
+#if (defined(__AVR__) || defined(ESP8266)) && !defined(__AVR_ATmega2560__)
+// For UNO and others without hardware serial, we must use software serial...
+// pin #2 is IN from sensor (GREEN wire)
+// pin #3 is OUT from arduino  (WHITE wire)
+// Set up the serial port to use softwareserial..
+SoftwareSerial mySerial(2, 3);
+
+#else
+// On Leonardo/M0/etc, others with hardware serial, use hardware serial!
+// #0 is green wire, #1 is white
+#define mySerial Serial1
+
+#endif
+
+
+Adafruit_Fingerprint finger = Adafruit_Fingerprint(&mySerial);
+
+void setup()
+{
+  Serial.begin(9600);
+  while (!Serial);  // For Yun/Leo/Micro/Zero/...
+  delay(100);
+  Serial.println("\n\nDelete Finger");
+
+  // set the data rate for the sensor serial port
+  finger.begin(57600);
+
+  if (finger.verifyPassword()) {
+    Serial.println("Found fingerprint sensor!");
+  } else {
+    Serial.println("Did not find fingerprint sensor :(");
+    while (1);
+  }
+}
+
+
+uint8_t readnumber(void) {
+  uint8_t num = 0;
+
+  while (num == 0) {
+    while (! Serial.available());
+    num = Serial.parseInt();
+  }
+  return num;
+}
+
+void loop()                     // run over and over again
+{
+  Serial.println("Please type in the ID # (from 1 to 127) you want to delete...");
+  uint8_t id = readnumber();
+  if (id == 0) {// ID #0 not allowed, try again!
+     return;
+  }
+
+  Serial.print("Deleting ID #");
+  Serial.println(id);
+
+  deleteFingerprint(id);
+}
+
+uint8_t deleteFingerprint(uint8_t id) {
+  uint8_t p = -1;
+
+  p = finger.deleteModel(id);
+
+  if (p == FINGERPRINT_OK) {
+    Serial.println("Deleted!");
+  } else if (p == FINGERPRINT_PACKETRECIEVEERR) {
+    Serial.println("Communication error");
+    return p;
+  } else if (p == FINGERPRINT_BADLOCATION) {
+    Serial.println("Could not delete in that location");
+    return p;
+  } else if (p == FINGERPRINT_FLASHERR) {
+    Serial.println("Error writing to flash");
+    return p;
+  } else {
+    Serial.print("Unknown error: 0x"); Serial.println(p, HEX);
+    return p;
+  }
+}